Permastone

CARE AND MAINTENANCE

Although NAFCO floors are durable, all floor coverings require some

care to look their best. Many problems can be prevented before they

occur. Special attention should be paid when selecting a floor for your

specific needs.

The type and frequency of traffic on your NAFCO floor will determine

the frequency of maintenance needed. The type of floor and even the

color will also have some bearing on how much care may be

necessary. For example, solid color floors will visually show scuffs,

scratches, dirt and general wear to a greater degree than multi-colors

of chips or patterns. Of course, white or light colors will visually show

staining to a greater degree than darker colors. For this reason, solid

color and white floors should receive special attention in regard to

preventive maintenance and the amount of care provided. Good

judgement when choosing the type and style of your new floor will help

prevent maintenance problems before the floor is even installed.

If Tarkett 400 or Tarkett 850 adhesives were used when installing your

floor, all traffic and furniture should stay off the floor for at least 24

hours to allow the adhesive to dry completely.

Quik-Stik tiles or Tarkett 800 adhesive installations may be walked

upon immediately after completion

NOTE: DO NOT WASH ANY INSTALLATION FOR 48 HOURS!

· In order to prevent indentations and scratches, use glass,

polished metal or other non-staining cups or casters with flat

under surfaces (see diagrams on pages 4 & 5).

· Protect your floor against burns. NAFCO floors can be damaged

by burns from the glowing end of a cigarette, matches, or other

extremely hot items.

· Protect your floor from tracked-in dirt and grit particles by using

mats at all outside entrances. Take the time to remove any

imbedded grit particles from shoe soles before entering the room.

Avoid the use of rubber or latex-backed mats, as certain rubber

compounds can permanently stain vinyl (consult the mat

manufacturer to determine if their backing will stain vinyl).

Avoid tracking in tar or asphalt from driveways, as this can also

discolor vinyl.

· Avoid stilleto or damaged high heels on your floor. They can

cause permanent damage.

· All NAFCO floors have good resistance to stains. They are not

affected by most common household spills; however, any spill

should be cleaned up immediately. The longer the spilled material

is left on the floor, the greater the risk of permanently staining the

floor. For information regarding the proper method or solution to

use on a specific stain, see the chart on page 4.

· Avoid exposure to direct sunlight for prolonged periods, as this can

result in tile discoloration. Excessive temperatures might cause tile

expansion. During peak sunlight hours, the use of drapes or

blinds is recommended especially on patio doors, etc., that

receive direct sunlight.

RESIDENTIAL AND LIGHT COMMERCIAL

MAINTENANCE

Light daily sweeping or vacuuming will prevent dirt and grit particles from

being ground into the surface of the floor. If the floor is swept daily, a light

weekly washing should be sufficient. The type and frequency of traffic

will determine the frequency of maintenance needed. After the first

week or so, it will be necessary to use Tarkett SureShine® cleaner or an

equal neutral floor cleaner. Apply the SureShine® cleaner to the floor with

a sponge mop. After the soil deposits have been loosened from the floor,

mop thoroughly with clean water to remove them and all detergents, then

rinse the floor with clean, warm water to remove all soapy residue. Do

not flood the floor with water. Any detergent film left on the floor can

hold tracked-in dirt and leave the surface with a dull, cloudy

appearance.

NAFCO's factory Tritonite™ finish is resistant to scuffing, wear from

normal use, and common stains. However, the finish is not

indestructible and will scratch when subjected to harsh conditions.

NAFCO luxury vinyl tiles have a surface factory finish top coat. The

finish is applied during the manufacturing process and is either high

gloss or matte satin, depending upon the product style. All gloss levels

are maintained in the same way.

In time, high traffic areas may begin to show a reduction in gloss. When

this occurs, thoroughly clean and dry the floor. Apply a light coat of

Tarkett SureShine® Polish. To apply Tarkett SureShine® Polish, pour the

liquid in a shallow pan; dip in a sponge mop and wring it out gently,

leaving it saturated with the liquid polish. Mop in one direction to insure

uniform distribution. Do not mop too vigorously as this could cause

bubbles.

Continue to apply Tarkett SureShine® Polish to the floor until the entire

floor is evenly coated. SureShine® Polish dries in 30 minutes; if more than

one coat is desired, be sure to let each coat completely dry before

applying another. Keep in mind that 2-3 thin coats are better than one

heavy coat.

In time, it will be necessary to strip the old layers of Tarkett SureShine®

Polish and apply fresh coats. Strip the polish by using a high-quality

wax/polish remover.